Print this page
6064 ixgbe needs X550 support
Reviewed by: Tycho Nightingale <tycho.nightingale@pluribusnetworks.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
| Split |
Close |
| Expand all |
| Collapse all |
--- old/usr/src/uts/common/io/ixgbe/ixgbe.conf
+++ new/usr/src/uts/common/io/ixgbe/ixgbe.conf
1 1 #
2 2 # CDDL HEADER START
3 3 #
4 4 # The contents of this file are subject to the terms of the
5 5 # Common Development and Distribution License (the "License").
6 6 # You may not use this file except in compliance with the License.
7 7 #
8 8 # You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
9 9 # or http://www.opensolaris.org/os/licensing.
10 10 # See the License for the specific language governing permissions
11 11 # and limitations under the License.
12 12 #
13 13 # When distributing Covered Code, include this CDDL HEADER in each
14 14 # file and include the License file at usr/src/OPENSOLARIS.LICENSE.
15 15 # If applicable, add the following below this CDDL HEADER, with the
16 16 # fields enclosed by brackets "[]" replaced with your own identifying
17 17 # information: Portions Copyright [yyyy] [name of copyright owner]
|
↓ open down ↓ |
17 lines elided |
↑ open up ↑ |
18 18 #
19 19 # CDDL HEADER END
20 20 #
21 21 #
22 22 # Copyright(c) 2007-2008 Intel Corporation. All rights reserved.
23 23 #
24 24 # Copyright 2010 Sun Microsystems, Inc. All rights reserved.
25 25 # Use is subject to license terms.
26 26 #
27 27 # Copyright (c) 2013 Saso Kiselkov. All rights reserved.
28 +# Copyright 2016 OmniTI Computer Consulting, Inc. All rights reserved.
28 29 #
29 30 #
30 31 # Driver.conf file for Intel 10GbE PCIE NIC Driver (ixgbe)
31 32 #
32 33 # -------------------- Jumbo Frame --------------------
33 34 # default_mtu
34 35 # The size of the default MTU (payload without the ethernet header)
35 -# Allowed values: 1500 - 16366 (for Intel 82598 10Gb Ethernet controller)
36 -# 1500 - 15500 (for Intel 82599 10Gb Ethernet controller)
36 +# Allowed values: 1500 - 16366 (for Intel 82598 Ethernet controller)
37 +# 1500 - 15500 (for Intel 82599, X540, X550 Ethernet controller)
37 38 # Default value: 1500
38 39 #
39 40 # default_mtu = 1500;
40 41 #
41 42 # -------------------- Flow Control --------------------
42 43 # flow_control
43 44 # Ethernet flow control
44 45 # Allowed values: 0 - Disable
45 46 # 1 - Receive only
46 47 # 2 - Transmit only
47 48 # 3 - Receive and transmit
48 49 # default value: 0
49 50 #
50 51 # flow_control = 3;
51 52 #
52 53 # -------------------- Transmit/Receive Queues --------------------
53 54 #
54 55 # tx_ring_size
55 56 # The number of the transmit descriptors per transmit queue
56 57 # Allowed values: 64 - 4096
57 58 # Default value: 1024
58 59 #
59 60 # rx_ring_size
60 61 # The number of the receive descriptors per receive queue
61 62 # Allowed values: 64 - 4096
|
↓ open down ↓ |
15 lines elided |
↑ open up ↑ |
62 63 # Default value: 1024
63 64 #
64 65 # mr_enable
65 66 # Enable multiple tx queues and rx queues
66 67 # Allowed values: 0 - 1
67 68 # Default value: 1
68 69 #
69 70 # rx_group_number
70 71 # The number of the receive groups
71 72 # Allowed values: 1 - 16 (for Intel 82598 10Gb ethernet controller)
72 -# Allowed values: 1 - 64 (for Intel 82599 10Gb ethernet controller)
73 +# Allowed values: 1 - 64 (for Intel 82599, X540, X550 10Gb ethernet controller)
73 74 # Default value: 1
74 75 #
75 76 # allow_unsupported_sfp
76 77 # Allow use of unsupported (non-Intel) SFP modules in adapters with
77 78 # pluggable optics
78 79 # Allowed values: 0 - 1
79 80 # Default value: 0
80 81 #
81 82 # -------- How to set parameters for a particular interface ---------
82 83 # The example below shows how to locate the device path and set a parameter
83 84 # for a particular ixgbe interface. (Using flow_control as an example)
84 85 #
85 86 # Use the following command to find out the device paths for ixgbe,
86 87 # more /etc/path_to_inst | grep ixgbe
87 88 #
88 89 # For example, if you see,
89 90 # "/pci@7b,0/pci10de,5d@e/pci8086,a15f@0" 0 "ixgbe"
90 91 # "/pci@7b,0/pci10de,5d@e/pci8086,a15f@0,1" 1 "ixgbe"
91 92 #
92 93 # name = "pciex8086,10c6" parent = "/pci@0,0/pci10de,\<pci10de\>5d@e" unit-address = "0"
93 94 # flow_control = 1;
94 95 # name = "pciex8086,10c6" parent = "/pci@0,0/\<pci\>pci10de,5d@e" unit-address = "1"
95 96 # flow_control = 3;
|
↓ open down ↓ |
13 lines elided |
↑ open up ↑ |
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX